Advertisement

Search Articles:



Picking the Right Wood Floor Finish Applicator

By Bill Costello
October/November 2008
print  Print          Download PDF

Between rollers, T-bars, lambswool applicators, brushes and the occasional rag, there are so many ways to get finish on your floor that figuring out what to use can be confusing. Here is a simple way to break down the proper applicators for the four most commonly used finish types. As always, defer to the finish manufacturer's instructions, be sure to use the right respirator, and have your MSDS on hand.

Oil-Modified Polyurethane

The trick to oil-modified polyurethane (frequently called "poly") is generally "more is better;" you don't want the finish to puddle, but you want to get as much on the floor as possible and spread it as fast as possible to get the smoothest appearance on the floor. There are oldschool methods and newer methods to accomplishing this. Many old timers in the industry like to use a China bristle brush. These brushes are made of hog's hair, which are actually hollow inside. The brush sucks up finish, which gets released as you glide the finish onto the floor. Many people claim this is the best method for applying finish, since you're so much closer to the floor and you can see missed spots ("holidays") or blemishes in the finish and correct the problem before it dries. China bristle brushes can be cleaned off with just mineral spirits.

Another old-school applicator for oil-modified is the lambswool applicator on the block, which is made from either 100 percent lambswool or synthetic lambswool. Again, like the China bristle brush, this applicator holds a lot of finish. Natural lambswool tends to hold more finish than synthetic, but the synthetic definitely still does the job and is a little cheaper, which is why I think it's seen more in the industry. With the lambswool on the block, unlike the brush, you're standing upright and away from the floor, which means you have to be a little more careful as you're applying to make sure you're not making any mistakes.

There are some other caveats to the lambswool. Recently purchased natural lambswool applicators tend to shed fibers that get stuck in the finish, so before using one, simply comb out the applicator with a pocket comb or wrap it up in blue tape and remove the tape. Other guys might wash it without detergent and let it dry. This is used for the first coat of finish. For subsequent finishes, use lambswool applicators you've already used on at least 500 to 1,000 feet of finish; this gives a much smoother application. Lambswool applicators need to be stored in either mineral spirits or polyurethane.

Some of the newer applicators are making finish application even easier. Just like your transition from riding a tricycle to a bike with training wheels to a standard bike, you work up from old-school applicators to new-school. A T-bar applicator, especially with tapered ends, is great for applying any finish. It allows you to get around doorjambs, and it puts a lot of finish down faster than a lambswool applicator. Some companies also manufacture a lambswool sleeve that can be slipped onto a T-bar. This speeds up application, and it also holds a lot of finish. Another option is rolling finish on with a ¼-inch or 3/8 -inch roller. This gets the finish down fast and agitates the floor very little (more agitation to the finish makes it look worse).

Waterborne Urethane

All the applicators for water-based urethane are synthetic. When applying this type of finish, you definitely don't want to use a China bristle brush or lambswool applicator because the two hold a lot of finish and, unlike oil, you don't want all that on the floor; water-based is designed to go down thinner. Synthetic applicators just spread finish; they don't hold any finish in them. Many of the same synthetic applicators, except lambswool, can be used with water-based: a synthetic pad on a block, a T-bar with a synthetic sleeve or a roller. The cut-in pad you use for the edges of the flooring should also be synthetic.

Moisture-Cure Urethane

Many guys have different systems for applying moisture cure finish, which is mostly used on the East Coast. With this finish, contractors tend to use a brush—either a 6-inch China bristle or 12-inch brush—as opposed to the T-bar. It's a fast-applying finish, so using a roller also works.

Conversion Varnish

One of the most efficient ways to apply conversion varnish, which is also called "acid-cure" or "Swedish" finish, is with a brush. Contractors can choose between a 6-inch China bristle or a 12-inch brush, but the main point is to get down so you can see the finish being applied. Conversion varnish has a tendency to separate and leave missed spots, so if you're down on your knees applying with a brush, you can see anything that's missed. As with many finishes, conversion varnish can also be applied with a roller. Here, you have to follow the manufacturer's recommendations for which sleeve to use on the roller, and you have to be certain you're applying enough finish. Application of this finish is easy, but typically the cleanup is more involved, requiring a lacquer thinner.

Using the proper applicators for each finish and getting the correct spread rate is essential to making that finish look great. Using the best applicator for that type of finish, and following the manufacturer's instructions, will help you "get 'er done."



Bill Costello is an Olive Branch, Miss.-based southeast account manager for finish manufacturer Dura Seal.



Applicator    Finish                           

 Comments:

I change from lambswood block to roller on the last year and dispite that I had not a single issue related to marks ,paddles or lines common on other methods of application I find a costumer that complain about a different texture on the finish that do not show on the eyes but you fill a little rugged .....anybody can tell me what it is and how to avoid?
WF  Owner  9/25/2010 1:21:41 PM


Name:
Job Title:
Email (not published):
Comment:
(maximum 2,000 characters)  

Related Articles: Sanding and Finishing

The Quest for Colors: Don't Go Astray With Custom Stain Colors (June/July 2014 - Paul Campbell)
Through many conversations with wood flooring contractors over the years, there seems to be a common thread—color is...

The Missing Link: Are You Skipping a Step in Your Recoats? (June/July 2014 - Michael Purser)
Recoating wood floors is a great option for finishes going through a midlife crisis. Quick and clean, it is still...

A Holt Sander From 1939, And It Still Works (June/July 2014 - Andrew Averill)
Brian Franklin has been hunting for valuable and overlooked antiques since the 1980s, so he knew he’d found something when he came across a 1939 Holt sander at an estate sale in Oregon.

Trick of the Trade: In the Bag (June/July 2014 - HF Editors)
Ever find yourself ready to put on that final coat but missing your booties that protect the floor from your work shoes? Here’s...

Tales From the Front: In Hot Pursuit (June/July 2014 - HF Editors)
HF Inspector Blogger Roy Reichow, founder at National Wood Floor Consultants Inc. in East Bethel, Minn., remembers a job where...

Top of the Tower: Lugging A 120-Pound Sander Up Three Flights (June/July 2014 - Andrew Averill)
How long would it take you to climb two flights of stairs and another set of steps mortised—near vertically—into the wall... while lugging a 128-pound sander?

Improve Your Jobs by Understanding the Stages of Finish Curing (April/May 2014 - Micah Petersen)
Is it dry yet”? and “How much longer”? are common questions asked when finish is curing...

Trick of the Trade: Modify Your Corner Scraper for More Uses (April/May 2014 - Kim Wahlgren )
This issue’s tip comes from Michael Dittmer, owner at Putnam, Ill.-based Michael Dittmer Wood Floors and NWFA Regional Instructor...

Q&As: Stain Solutions for Wood Floors (February/March 2014 - HF Editors)
My customer wants the color of walnut but hates the walnut grain. Somebody suggested...

Resurfacing History: Volunteers Refinish 100-Year-Old Battleship (February/March 2014 - Michael Popke)
Last June, a volunteer working to restore the 30,000 square feet of wood deck space on the battleship USS Texas brought...

12345678910...>>
CONNECT WITH HF
FEATURED SUPPLIERS